Spawn and Substrates

How to Pasteurize Straw for Mushroom Growing: Hot Water and Cold Methods

Learn how to pasteurize straw for mushrooms using the hot water method or cold water lime soak, with temperatures, times, draining and safety tips.

On this page
  1. Why pasteurize straw
  2. Prepare the straw
  3. Method 1: hot water pasteurization
  4. Method 2: cold water lime pasteurization
  5. Draining and the squeeze test
  6. Inoculating
  7. Safety
  8. Troubleshooting
  9. Which method should you use?

Why pasteurize straw

Raw straw carries molds, bacteria and other organisms that compete with mushroom mycelium. Pasteurization reduces them without fully sterilizing the straw, which leaves some beneficial microbes alive and gives your spawn a head start. It is the usual preparation for straw-based oyster mushroom grows, and it needs much less equipment than pressure sterilization. For a comparison with other materials, see the best substrate for mushroom cultivation.

The two most common home methods are hot water pasteurization and cold water lime pasteurization.

Prepare the straw

Use clean, dry, mold-free straw. Wheat straw is a popular choice, and other cereal straws are used too. Avoid hay, which contains seeds and often decomposes more readily. Chop the straw into pieces roughly 1 to 3 inches (about 2.5 to 7.5 cm) long, using a shredder, a garden machine or shears. Shorter pieces pack more evenly and are easier to handle.

Method 1: hot water pasteurization

This method suits small to medium batches and needs no chemicals.

  1. Place the chopped straw in a mesh bag, a pillowcase or a wire basket so you can lift it in and out.
  2. Heat a large pot, drum or cooler of water to about 160 to 180°F (about 71 to 82°C). Use a thermometer. Boiling water is hotter than needed and may be harder to manage.
  3. Submerge the straw and weigh it down so that it stays under water.
  4. Hold the temperature for roughly one to two hours, adding heat as needed, since the straw will cool the water.
  5. Lift out the bag and let it drain (see below).

Water temperature will drop once the cold straw goes in, so check it often. If the temperature falls well below the range, extend the time or reheat.

Method 2: cold water lime pasteurization

This approach raises the water’s pH using hydrated lime (calcium hydroxide), which discourages many competing microbes. It suits larger batches and avoids heating large volumes of water.

  1. Fill a clean container, such as a drum or tub, with cold water.
  2. Add hydrated lime. A figure often quoted is about 2 grams per liter of water, which works out to roughly 300 grams for a 55-gallon drum. Different sources suggest different amounts, so follow a trusted guide and use low-magnesium hydrated lime.
  3. Stir to dissolve, and add the chopped straw. Weigh it down so it is fully submerged.
  4. Leave it to soak for around 12 to 24 hours, often overnight.
  5. Drain it thoroughly, for an hour or more, so the excess liquid runs off and the pH comes back down before spawn goes in. Guides often quote a finished pH of around 8.5 or lower. See substrate pH for mushroom growing for why alkalinity matters.

Draining and the squeeze test

Pasteurized straw should be damp, not dripping. Let it drain until it has cooled to roughly room temperature. A common check is the squeeze test: squeeze a handful firmly, and you should see no more than a drop or two of water. Straw that is too wet can lead to bacterial problems, and straw that is too dry can slow colonization.

Inoculating

Once the straw has cooled, mix in spawn quickly using clean hands and a clean container, then pack it into bags or buckets with ventilation. Using more spawn gives the mycelium a stronger head start. For the details, see mushroom spawn explained, and for tips on colonization speed see what helps mycelium grow faster.

Safety

  • Hydrated lime can irritate skin, eyes and lungs. Wear gloves, eye protection and a mask or respirator, and add it to water carefully to avoid dust.
  • Hot water can cause scalds. Take care lifting heavy, hot, wet bags.
  • Do not use cleaning chemicals or bleach unless you are following a method designed for it, and keep everything away from children and pets.

Troubleshooting

  • Green or black mold in the bag. If it is green, check whether it is Trichoderma. The straw may not have been pasteurized for long enough or at a high enough temperature, the spawn rate may have been low, or the straw may have been too wet.
  • Sour or rotten smell. Often a sign of bacterial growth in overly wet or under-treated straw.
  • Slow colonization. The straw may be too dry, the room too cool, or the lime-treated straw not drained well enough.

Which method should you use?

Hot water is relatively quick and suits small batches. Lime is a good option when you need to handle many kilos of straw. Either can work well when you maintain the correct conditions. If you are working with nutrient-rich substrates such as supplemented sawdust, these methods are generally not enough, and pressure sterilization is used instead. See how long to pressure cook mushroom substrate and grain jars and Master’s Mix.

The complete guide to spawn and substrates

Mushroom Spawn Explained: Grain Spawn Sawdust Spawn and Mycelium
Read the guide

Keep exploring

Guides from other topics

All topics →