Which mushrooms suit bucket growing
Growing in a bucket is an affordable, beginner-friendly method that works best with fast-growing species that fruit from the side of a block. Oyster mushrooms are the standard choice, and some growers also have success with others such as lion’s mane, though results vary. Species that need specialized substrates or conditions, such as shiitake on supplemented sawdust, are usually grown in blocks or on logs instead.
The bucket acts as a mini fruiting chamber: the sides hold moisture in the substrate, and the mushrooms emerge from the holes you drill.
What you need
- A clean 5-gallon bucket (about 19 litres) with a lid. Food-grade buckets are a sensible choice since the substrate will sit inside for weeks.
- A drill and bits. A bit of roughly 1/4 to 1/2 inch (about 6-13 mm) for the side holes, and a small bit for bottom drainage.
- Substrate such as chopped straw, hardwood chips or hardwood pellets and sawdust, depending on the species and your supplier’s advice. Amounts vary with the bucket and material, so follow the instructions that come with your spawn.
- Spawn matched to the substrate, such as grain spawn or sawdust spawn (see mushroom spawn explained). The amount used varies by method, and recommendations in common guides range from a few ounces to a few pounds for a bucket. Check the supplier’s instructions.
- A way to pasteurize the substrate: a large pot or tote with hot water, or hydrated lime for a cold pasteurization method.
- A spray bottle, a plastic bag or micropore tape, and a knife for harvesting.
- Gloves and a cleaning solution such as soap and water or isopropyl alcohol.
Holes layout
The holes are where the mushrooms will emerge, so the layout affects how many clusters you get and how they grow.
- Side holes: a common layout is a staggered or diamond pattern around the circumference, with holes spaced roughly 4-6 inches (10-15 cm) apart, giving around 10-20 holes in total. The hole diameter in typical guides is about 1/4 to 1/2 inch. Smaller holes keep the substrate moister but can produce smaller clusters, while larger holes allow bigger clusters but dry out faster.
- Rows: two or three rows of holes, offset from one another, are common. Keep the lowest row a few inches above the bucket base and the highest row below the top layer of substrate.
- Bottom holes: a few small holes, such as 1/8 inch (3 mm), let excess water drain. Stand the bucket on a tray or on bricks so it does not sit in water.
- Edges: smooth rough plastic edges and clean up shavings so the mushrooms are not scratched and nothing falls into the substrate.
Do not worry about getting the pattern exactly right. Most growers adjust their layout on later buckets.
Preparing the substrate
Straw and wood chips carry competing microbes, so they are usually pasteurized before use. Two common methods, covered in more depth in how to pasteurize straw for mushroom growing:
- Hot water: soak chopped straw or chips in hot water at roughly 160-185 °F (about 70-85 °C) for around 30-60 minutes. Some guides let it soak longer. Use a thermometer to check temperature.
- Lime bath: soak the material in water with hydrated lime to raise the pH (about 12.5 is often quoted), then drain. Wear gloves, eye protection and a dust mask because lime is caustic.
Drain thoroughly and allow the substrate to cool to room temperature. It should feel damp like a wrung-out sponge, not dripping.
Filling and inoculating the bucket
- Wipe out the bucket and wash your hands.
- Add a layer of substrate a few inches deep, then a sprinkling of crumbled spawn.
- Repeat in layers, pressing gently so the layers touch. Place spawn near the holes so mycelium can reach them.
- Fill to the top, press down and close the lid, or cover with a loosely fitted plastic bag. Some growers cover side holes with micropore tape during colonization to reduce drying and contamination.
Clean technique matters here. For more rigorous clean work with cultures, see our guide to the still air box, though you do not need one for bucket growing with purchased spawn.
Colonization
Keep the bucket out of direct sun at a comfortable room temperature. Common guides give around 65-75 °F (about 18-24 °C) for many oyster varieties, and the mycelium typically binds the substrate in one to three weeks, depending on species, temperature and spawn rate. See colonization timelines by species. If you have a cold house, an incubation chamber can help.
You should see white mycelium spreading through the substrate and appearing at the holes. Keep it covered until it is mostly colonized.
Fruiting
Move the bucket to a bright, shaded, humid place with fresh air, such as a covered porch, a basement with light, or a spot inside a tent. Remove the tape or bag from the holes. Mist the holes and any pins gently with clean water a couple of times a day, more often if the air is dry. Avoid leaving standing water on the substrate or inside the holes.
Pins should appear within days to a couple of weeks. If your room is dry, you can place the bucket in a humid chamber or tent or loosely cover it with a bag, making sure air can still move.
Harvest and more flushes
Harvest oyster clusters when the caps are flat or just beginning to curl at the edges, by twisting at the base or cutting with a clean knife. Continue misting and wait for the next flush, which often arrives after one to two weeks. Yields normally fall with each flush, and most growers stop after a few. See mushroom flushes explained. Once the bucket stops producing, or if it shows contamination, you can compost the spent substrate.
Troubleshooting
- No mushrooms from the holes. Check humidity and fresh air, and make sure the substrate is fully colonized.
- Mushrooms dry out or crack. Increase humidity and mist more often, or move to a humid spot.
- Long stems and small caps. Not enough fresh air. Move to a better-ventilated location.
- Green, black or slimy patches, or a sour smell. Likely contamination (see green mold on mushroom substrate). Remove the bucket from your growing area. Do not eat mushrooms from contaminated substrate.
- Water pooling inside. Check the drainage holes and avoid over-wet substrate.
If you want to grow in bulk substrate in a single container with more environmental control, see our monotub guide.