What a shotgun fruiting chamber is
A shotgun fruiting chamber (SGFC) is a clear plastic bin riddled with small holes, like the pattern left by a shotgun blast, with a layer of damp perlite in the bottom. The holes let fresh air in and carbon dioxide out, while the perlite and the plastic walls help hold humidity. You place colonized blocks or cakes inside to fruit. To judge when a block is ready, see when to fruit a mushroom bag.
It is one of the cheapest chambers to build and a common first project. It also takes some daily attention, since it relies on manual misting and fanning. For how it compares with other setups, see our overview of mushroom growing chambers.
Materials and tools
- A clear plastic storage bin with a lid. Larger bins give more room, with 60 litres or more suggested in some guides. Clear or translucent plastic lets light in. Choose a bin that is not brittle, since you will drill many holes.
- Perlite. Enough for a layer a few centimeters deep.
- A drill and bit. A bit of around 6 mm (about 1/4 inch) is a common choice for small holes. Some growers use larger ones.
- A spacer or rack to hold your substrate above the perlite, such as a plastic mesh, a plastic grid or an upturned tray with holes.
- A hygrometer (optional but recommended).
- A spray bottle with clean water.
- Isopropyl alcohol and paper towels for cleaning.
Step-by-step build
- Clean the bin with soap and water, then wipe with isopropyl alcohol. Let it dry.
- Mark the holes. Mark a grid on the sides, lid and base. Hole spacing varies between guides. One guide suggests roughly 15 cm apart, while others use closer spacing for better airflow and humidity distribution. Start wider if you live in a dry climate and want to hold humidity, and add holes later if mushrooms show signs of too much CO2.
- Drill the holes through the sides, lid and base. Use steady pressure and a sharp bit so the plastic does not crack. Drilling the base lets excess water drain, so place the bin on a tray.
- Smooth the edges. Remove plastic burrs with a blade or sandpaper so they do not catch on blocks or hands.
- Rinse the bin to remove plastic dust, then wipe it down again.
- Add perlite. Pour in a layer roughly 5-7 cm deep, as suggested in one guide, or at least a few centimeters. Wear a dust mask if the perlite is dry and dusty.
- Saturate the perlite. Soak it with clean water, then let the excess drain out through the base holes. It should be damp, not sitting in water.
- Add a hygrometer where you can read it, either inside the bin or visible through the holes.
- Add your spacer. Place a rack or grid so your substrate sits clear of the wet perlite, ideally at least a couple of centimeters above it.
- Add your colonized block or cake. Put it on the spacer, close the lid and note the date.
Running the chamber day to day
- Mist the perlite and inner walls, not the mushrooms or the substrate directly. Droplets on caps can cause blotches.
- Fan once or twice a day. Remove the lid and gently wave a clean object or your hand over the bin to swap the air, then close it. This clears built-up CO2.
- Check humidity. Many gourmet species fruit best at high humidity, often around 85-95% (see mushroom growing conditions). If the hygrometer reads low or the perlite looks dry, rewet it. For more detail, read whether perlite alone keeps a chamber moist.
- Provide light. Indirect daylight or a modest LED for about 12 hours a day.
- Harvest promptly when the mushrooms are ready, and remove old stems. Mushroom fruiting stages shows what ready looks like.
What it suits and what it doesn’t
A shotgun chamber suits small to medium fruiting jobs: a few blocks, cakes or kits. It does not suit large bulk grows, and in dry rooms or strong air conditioning it can be hard to keep humid. If you want to grow in bulk substrate, a monotub is usually easier. For bigger yields, consider a grow tent setup.
Troubleshooting
- Mushrooms dry out or pins abort. Increase humidity: add more water to the perlite, mist walls more often, reduce fanning, or cover some holes with micropore tape.
- Long stems and small caps. More fresh air is probably needed. Fan more often or add holes.
- Water pools at the bottom. Perlite was over-saturated or the base holes are blocked. Drain it.
- Mold or green growth in the perlite or on the substrate. Remove the affected material, clean the bin, and replace the perlite. See green mold on mushroom substrate. Review hygiene and humidity.
- Sour or off smells. Bacterial contamination may be present. Remove the block and do not eat it.
Cleaning and reuse
Between grows, wash the container thoroughly. One guide suggests washing after every one or two flushes. Replace perlite if it turns discolored or smells off. Some growers reuse perlite by rinsing it in a dilute bleach solution, such as about 1 part bleach to 10 parts water, then rinsing thoroughly and drying before reuse. Handle bleach carefully, ventilate the area, and never mix it with other cleaners.
Upgrading
If the shotgun chamber works but you outgrow it, options include a bigger bin, adding a small humidifier, or stepping up to a tent. A fish-tank style or heated box can handle the warm colonization stage separately, leaving the shotgun chamber for fruiting only.