What a monotub is and why growers use it
A monotub is a single large plastic storage tub modified so that mushrooms can colonize and fruit in the same container. Instead of moving blocks or bags into a separate chamber, you mix colonized grain spawn with a bulk substrate inside the tub, let the mycelium take over, then open up the airflow so mushrooms can form on the surface.
Growers like monotubs because they are inexpensive, reusable, and hold humidity well while still allowing some air exchange. They are widely used for bulk grows of species that fruit from a surface, and they work as a simple chamber for home mushroom growing.
What you need
- A tub. A clear plastic tote with a lid, often around 50-66 quarts (roughly 50-60 litres). Clear walls make it easy to see what is going on.
- Colonized grain spawn. Rye, oats, millet or similar grain that is fully overgrown with your chosen mushroom’s mycelium.
- Bulk substrate. A common choice is a coco coir, vermiculite and gypsum mix, often called CVG. Pasteurized manure-based or straw substrates are used for other species. Match the substrate to the species, as covered in the best substrate for mushroom cultivation.
- A liner. A piece of dark plastic, such as a trash bag, cut to fit inside.
- Filter material. Micropore tape, polyfill, or adhesive filter discs over the holes.
- Cleaning supplies. 70% isopropyl alcohol, clean water, a spray bottle and gloves.
Prices vary by supplier and region. Pre-made monotubs and kits are available if you would rather not drill your own.
Building the tub
- Clean the tub with soap and water, then wipe it with isopropyl alcohol.
- Drill holes. A common layout is several holes along the upper sides, spaced a few inches apart, plus a few more lower down. Many growers use holes of roughly 1-2 inches (2.5-5 cm), though layouts differ. Smooth any rough plastic edges.
- Cover the holes with filter discs, polyfill, or micropore tape. This keeps out contaminants while still letting some air through. During early colonization many growers keep the holes closed more tightly and open them later for fruiting.
- Add a liner. A dark liner around the inside walls encourages the mushrooms to form on the surface of the substrate instead of against the sides. The liner shrinks along with the substrate as it loses moisture and helps limit side pinning.
Preparing spawn and bulk substrate
Break up your fully colonized grain spawn into small pieces, roughly marble to nickel sized. Mix it with the pasteurized or prepared substrate to a ratio recommended for your recipe. Spawn-to-substrate ratios in common guides run from about 1:2 to 1:3, but check the instructions for your chosen species and substrate.
Substrate should be at field capacity, meaning moist but not dripping. If you squeeze a handful, only a drop or two of water should come out.
Add the mix to the tub, spread it evenly and pat it down gently. Many growers add a thin layer of plain substrate on top to cover exposed grain, which reduces the chance of contamination taking hold on loose kernels. Then put the lid on.
Work cleanly: wash hands, wipe surfaces and avoid opening the tub in a drafty room. For more rigorous techniques see our guides to the still air box and the home mycology lab.
Colonization
Colonization is the phase where the mycelium spreads through the substrate. Keep the tub in a dark or dim spot at a temperature suited to your species, commonly in the low-to-mid 70s °F (about 21-24 °C) for many gourmet species. Keep the lid on and holes mostly covered so CO2 and moisture stay in. Avoid opening it often.
Within roughly a week or two you should see white, thread-like or fluffy mycelium spreading across the surface. The exact timing depends on the species, spawn rate and temperature (colonization timelines by species). Wait until the surface is mostly covered before moving on. A tub in an incubation chamber or a warm closet can help keep temperature steady.
Fruiting
Once the surface is well colonized, switch to fruiting conditions:
- Increase fresh air. Remove plugs, switch to breathable filters or crack the lid so CO2 can escape.
- Add light. Indirect room light or a modest LED on a day-night cycle is typically enough.
- Watch humidity. Look for fine condensation on the walls and lid. If the surface looks dry, mist the tub walls lightly with clean water rather than soaking the mushrooms.
- Wait for pins. Small pinheads usually appear within days to a couple of weeks after conditions change.
Fan the tub gently once or twice a day if you are using a manual setup.
Harvesting and rehydrating for more flushes
Harvest when caps have opened as recommended for your species, for example before the caps flatten out and release large amounts of spores on many gourmet types. Twist and pull from the base, or cut cleanly with a sharp, clean knife.
After a flush, remove leftover stems and debris. The substrate may look dry. Rehydrating it by soaking or floating the block in clean, cool water for several hours, then draining it, can prepare it for another flush. Return it to the tub and repeat the fruiting conditions. Yields usually decline with each flush, and most growers stop after a few. See mushroom flushes explained.
Common monotub problems
- Mushrooms pinning on the sides. Often linked to missing or poorly fitting liners, or uneven substrate depth.
- Stalled colonization. Check temperature, substrate moisture and spawn health. See what helps mycelium grow faster. Too wet or too dry substrate both slow growth.
- Long stems, small caps. Typically a sign of too much CO2. Increase fresh air.
- Dry surface or aborted pins. Humidity may be too low or airflow too strong. Cut back on drafts and mist walls lightly.
- Green, black, or strongly sour-smelling growth. Possible contamination by mold or bacteria (see green mold on mushroom substrate). Isolate the tub and do not eat anything from it. If in doubt, discard and start again with cleaner technique.
Monotub vs other chambers
A monotub is a good middle option: easier to set up than a tent, more capable than a shotgun fruiting chamber, and well suited to bulk substrate. If you want to grow a few clusters of oysters out of a bin of straw, a bucket may be simpler. For bigger volumes or several species, a Martha tent offers more room.